RAD Data comm Vmux-210 Specifications Page 157
- Page / 192
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics
Vmux-210 Ver. 1.1 General Troubleshooting 6-15
List of Vmux-210 Alarms
Table 6-7
lists the Vmux-210 alarms according to their identification codes.
Table 6-7. Vmux-210 Alarms
ID Code Terminal Message Description Severity
3 SWITCH OF DB Occurred The Vmux-210 database has been replaced Event
18 DB UPDATE Occurred The Vmux-210 database has been updated Event
44 FAN No. 1 FAILURE Fan no. 1 not working Major
45 FAN No. 2 FAILURE Fan no. 2 not working Major
60
DEFAULT DB LOADED ON
STARTUP
No db or incompatible db existed in NVRAM on startup Event
80
BPV ERROR HAS
OCCURRED
A bipolar violation error has been detected on the E1/T1
port
Event
81 EXCESSIVE ERROR RATIO The bit error rate of the port exceeds 1×10
-3
Major
82 ALARM INDICATION SIGNAL
AIS is being detected at the E1/T1 port Major
83
EXCESSIVE BIPOLAR
VIOLATION
Excessive BPVs at the E1/T1 port Major
84
T1/E1 FRAME SLIP HAS
OCCURRED
A frame slip occurred at the E1/T1 port Event
87 T1/E1 SIGNAL LOSS Loss of input signal at the E1/T1 port Major
88 AIS RED ALARM
Local loss of frame synchronization at the E1/T1 port
caused by AIS condition
Major
89
LOC SYNC LOSS
(RED ALARM)
Local loss of frame synchronization at the E1/T1 port Major
90
REM SYNC LOSS
(YELLOW ALARM)
Remote loss of frame synchronization at the E1/T1 port Major
92 NETWORK LLB
T1 uplink port entered Local Loopback mode following
FDL command from network
Minor
93 NETWORK PLB
T1 uplink port entered Payload Loopback mode
following FDL command from network
Minor
97
LOCAL MULTIFRAME
ALARM
Local loss of multiframe synchronization at the E1 port Minor
98
REMOTE MULTIFRAME
ALARM
Remote loss of multiframe synchronization at the E1
port
Minor
100 CRC ERROR OCCURRED CRC-4 error in the E1 port receive signal Minor
130 MAIN LINK OVERFLOW
The required bandwidth exceeds the available
bandwidth on E1/T1/Serial uplink
Major
131 TRUNK IS DOWN A fault exists on the line. This alarm applies only to the
serial main link port with the DTE clock mode configured
and control signals enabled.
Major
132 UPLINK LOOP DETECTED When working with E1/T1 or Serial uplink, a loop exists
in the TDM network.
Major
195 BUNDLE IS OOS Bundle is out of service due to the network connectivity
problems
Major
- Vmux-210 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Declaration of Conformity 10
- Quick Start Guide 11
- 2. Configuring Vmux-210 12
- Figure 1. Quick Setup Menu 13
- Contents 15
- Chapter 1 19
- Introduction 19
- Applications 20
- Ethernet Links 21
- Serial Main Link 21
- Voice Interfaces 21
- TDMoIP Multiplexing 21
- AAL2oMPLS Multiplexing 21
- Bundling 22
- VLAN Table 22
- Internal Router 22
- Statistics Collection 23
- Management 23
- 1.2 Physical Description 24
- 1.3 Functional Description 25
- Signaling 27
- Compression 27
- Voice Activity Detection 28
- Ethernet Frame 28
- VLAN Support (per bundle) 30
- UDP Support 30
- E1/T1/Serial Main Link 31
- Integral Ethernet Switch 31
- DHCP Client Support 32
- Sec in this example) 33
- Chapter 2 41
- Installation and Setup 41
- 2.3 Package Contents 42
- 2.4 Equipment Needed 42
- Figure 2-1. FXS Connector 43
- Connecting to the E1 Link 44
- Connecting to the T1 Link 45
- Connecting to AC Power 46
- Connecting to DC Power 47
- Chapter 3 49
- Operation 49
- 3.2 Indicators 50
- PWR TST ALM 50
- 3.3 Default Settings 50
- Sec) 400 53
- Initiating a Control Session 56
- Logging In 57
- Selecting Parameters 58
- Using Terminal Hot Keys 59
- Sample Help Screen 59
- Security Levels 59
- Working with Telnet 60
- Working with ConfiguRAD 60
- Web Browser Requirements 61
- Logging in via a Web Browser 61
- Choosing Parameters 62
- Menu Map 63
- Change User 64
- Password 64
- 3.5 Turning Off the Unit 67
- Chapter 4 69
- Configuration 69
- Figure 4-2. Management Menu 71
- Setting Host IP Parameters 72
- Configuring the Manager List 72
- Managing Users 73
- Configuring Physical Ports 74
- Figure 4-7. Ethernet Menu 75
- Configuring the E1/T1 Uplink 78
- Table 4-11. T1 Parameters 79
- Configuring E1 Parameters 81
- Time Slot Table 82
- Configuring Analog Ports 83
- Configuring Ring Timeouts 84
- Configuring Ringer Profiles 84
- Configuring Gains 85
- Configuring Bundles 86
- Displaying all Bundles 87
- Adding a Bundle 88
- Editing a Bundle 89
- Figure 4-25 90
- Figure 4-26 90
- Figure 4-30 90
- Figure 4-23 90
- Figure 4-24 90
- Table 4-23. TOS Parameters 91
- VLAN Tagging is set to Yes 92
- Coder/Rate = G.729A/ 93
- Figure 4-27. Fax/Modem Menu 94
- Figure 4-28. VAD Menu 96
- Table 4-28. VAD Parameters 96
- Deleting a Bundle 99
- Configuring the Bridge 102
- Configuring VLAN 103
- Displaying the VLAN Table 104
- Adding and Editing a VLAN 104
- Deleting a VLAN 105
- Configuring the Router 106
- Routing 109
- Configuring RIP Parameters 110
- Figure 4-45. RIP Menu 111
- Table 4-43. RIP Parameters 111
- Figure 4-46. Firewall Menu 112
- Configuring Static Routing 113
- Displaying all Static Routes 114
- Adding a Static Route 114
- Editing a Static Route 115
- Deleting a Static Route 115
- Configuring DHCP Server 116
- Adding a DHCP Server Pool 117
- Editing a DHCP Server Pool 117
- Deleting a DHCP Server Pool 118
- Adding a NAT 119
- Editing a NAT 119
- Notes: 121
- Deleting a NAT 122
- Figure 4-61 123
- Displaying Existing Rules 125
- Adding Firewall Rules 125
- Editing Firewall Rules 125
- Deleting Firewall Rules 126
- 4.3 Additional Tasks 127
- Boot Sequence 128
- Accessing the File System 128
- Figure 4-65 130
- Figure 4-66 131
- Table 4-58 131
- Restoring Default Settings 132
- Setting the Date and Time 133
- Figure 4-70 134
- Resetting Vmux-210 135
- Chapter 5 137
- Configuring Vmux-210 for 137
- 5.2 Configuration Sequence 138
- 5.4 Configuring Vmux-210 140
- Appendix B 142
- Chapter 6 143
- Troubleshooting and 143
- Diagnostics 143
- Displaying Bundle Statistics 144
- Tracking Packets 146
- Figure 6-2 147
- Figure 6-4 147
- Table 6-2. Packets Tracking 147
- 6.2 Detecting Errors 154
- 6.3 Handling Alarms 156
- List of Vmux-210 Alarms 157
- 6.4 General Troubleshooting 158
- 6.5 Testing Vmux-210 159
- Loopback Tests 161
- Pinging Remote Devices 162
- Displaying the Active Tests 163
- 6.7 Technical Support 168
- Appendix A 169
- Connector Pinouts 169
- A.2 CONTROL Connector 170
- Table A-3 171
- Table A-4 171
- A.5 Serial Port 173
- Table A-7 174
- Table A-8 175
- Table A-9 176
- Table A-10 177
- Table A-11 178
- Table A-12 179
- Vmux-210 Ver. 1.1 182
- Vmux-210 Ver. 1.1 I-6 186
- Customer Response Form 187
- Error Report 189
- Innovative Access Solutions 192
Related products and manuals for Gateways/controllers RAD Data comm Vmux-210
(8 pages)© 2020, manymanuals.com. All rights reserved. | 0.245 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals