RAD Data comm Optimux-106 Specifications Page 19
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Operation Manual Quick Start Guide
Optimux-106 Ver. 6.1 Configuring the Optimux-106 3
3. Configuring the Optimux-106
Configuring IP Host Parameters
³ To define the Host IP parameters:
1. From the Management menu, select Host.
2. From the Host menu, perform the following:
Select IP Address to define the host IP address
Select IP Mask to define the host IP mask
Select Default Gateway to set the default gateway IP address.
The default gateway must be in the same subnet as the host.
Configuring Control Port Parameters
³ To configure the control port data rate:
1. From the Control Port menu (Configuration>System>Control Port), select
Baud Rate.
2. Select the terminal rate by typing the number corresponding to the desired
value, and then press <Enter>.
3. From the Control Port menu, select Security Timeout to set it to OFF or to 10
minutes.
4. From the Control Port menu, select Pop Alarm to set it to ON or to OFF.
Configuring the MNG-ETH port
³ To configure the MNG-ETH port:
1. From the Configuration menu select Physical Layer>Ethernet.
2. Select Device Number to set the device location (local or remote).
3. Select Port Number to set the Fast Ethernet port number to ETH-MNG.
4. Select Auto Negotiation to toggle between the Enabled and Disabled options.
5. Select Flow Control to toggle between the Enabled and Disabled options.
6. Select Alarms to mask or unmask the Fast Ethernet alarms. This option
identifies whether alarms triggered by this Ethernet port are masked or not.
When masked, these alarms are not trapped and are not recorded in the log
file.
Note
- Optimux-106 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Glossary 13
- Quick Start Guide 17
- 2. Connecting the Power 18
- Configuring the MNG-ETH port 19
- Contents 21
- Optimux-106 Ver. 6.1 iii 23
- Chapter 1 25
- Introduction 25
- 1.2 Physical Description 26
- 1.3 Functional Description 27
- Uplink Redundancy Option 28
- Alarms and Alarm Indications 29
- Management and Monitoring 31
- Physical Characteristics 31
- Power Requirements 31
- Plastic Enclosure 34
- Metal Enclosure 34
- Chapter 2 35
- Installation and Setup 35
- 2.2 Package Contents 36
- 2.3 Required Equipment 36
- 2.4 Mounting the Unit 37
- Connector Location 38
- Connecting to Channels 38
- Connecting to Alarm Relay 39
- Connecting to DCE 39
- 2.6 Grounding 40
- 2.7 Connecting to Power 40
- Caution 41
- Chapter 3 43
- Operation 43
- 3-1. Optimux-106 Indicators 44
- Device Information 45
- Logging In 47
- Choosing Options 48
- Navigating Tables 49
- Functional Screen Example 50
- Help Screen Example 50
- 3.5 Menu Map 51
- 3.6 Turning Off Optimux-106 52
- Chapter 4 53
- Configuration 53
- 4-2. Host IP Menu 54
- 4-2. Host Parameters 54
- Setting up the Manager List 55
- Changing a Password 56
- Listing Users 57
- 4-15. Link Menu 63
- 4-10. Uplink Parameters 63
- Configuring Local Redundancy 64
- Swapping the Software Files 65
- Viewing the Inventory 66
- Resetting Optimux-106 67
- Terminal Management Modes 67
- Chapter 5 69
- Monitoring and 69
- Diagnostics 69
- 5-2. System Status Screen 70
- 5-4. MNG-ETH Status Screen 72
- 5-5. USER-ETH Status Screen 73
- 5-6. Uplink Status Screen 74
- 5.2 Detecting Errors 75
- 5.3 Handling Alarms 75
- Displaying System Alarms 76
- Configuring Alarms 76
- List of Alarms and Events 77
- 5.4 Troubleshooting 78
- Setting Uplink Loopbacks 79
- Setting T1 Channel Loopbacks 80
- Local Optimux-106 82
- Remote Optimux-106 84
- Clearing the System Log File 85
- 5.7 Technical Support 86
- Chapter 6 87
- Software Upgrade 87
- Utilities Menu 88
- Activating the TFTP Server 89
- 6-2. TFTP Menu 90
- Telnet 91
- Using the XMODEM Protocol 92
- Using the TFTP 94
- Chapter 7 97
- Configuring a Typical 97
- Application 97
- Appendix A 99
- Pinouts 99
- A.3 Alarm Connector 100
- A.4 Control Connector 101
- Appendix B 103
- Optimux-106 MIBs 103
- B-2 Optimux-106 Ver. 6.1 104
- Customer Response Form 105
- Error Report 107
- International Headquarters 110
- North America Headquarters 110
Related products and manuals for Networking RAD Data comm Optimux-106
Networking RAD Data comm ASM-20 Specifications
(116 pages)
(116 pages)
Networking RAD Data comm T1 Specifications
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 2.116 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals