RAD Data comm Optimux-106 Specifications Page 49
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Operation Manual Chapter 3 Operation
Optimux-106 Ver. 6.1 Configuration and Management Alternatives 3-7
• Modify configuration and mode of operation, including setting system default
values
• View statistics and status
• Perform diagnostics.
Remote site configuration and system monitoring, including troubleshooting
procedures, can also be performed using Telnet or an SNMP application (e.g.,
RADview-HPOV/TDM).
Refer to
Figure
3-4
as a sample generic screen, to set up and configure
Optimux-106. Not all screen elements appear on all the screens.
• Link to a submenu, such as 1 or 2 on the sample screen. To reach a submenu,
select either 1 or 2 and press <Enter>
• Enter a value for a parameter (item 3). To enter a value, type 3, press <Enter>,
type the value and press <Enter>.
• Select a value from a list (item 4). To select a value, type 4, press <Enter>,
select the value from the list and press <Enter>.
• A value is changed by choosing a parameter (item 5) and pressing <Enter>.
The Save command is shown only when at least one menu item has been changed.
Illegal changes, such as a parameter out of range, disable Save.
The area at the bottom of the screen is allocated for online messages. These
messages carry online interactive user information containing configuration
instructions and failure information with possible reasons of the failure.
Navigating Tables
Terminal hot keys are provided per screen to enhance the functionality that is
required of that screen. The available hot keys are listed in the lower part of each
screen. The following hot keys are system keys, available on screens:
Esc Return to previous menu
! Return to the main menu
& Exit to password screen (to prevent unauthorized access after
completing the session)
X or x Next item
F or f Forward interval (statistic menus)
B or b Rearward interval (statistic menus)
@ - Full Screen Allocate full screen for messages
D Down
U Up (monitoring-->system screens)
Tab Select the next changeable cell
L Move left
R Move right
S <row No.><column No.> Select cell.
- Optimux-106 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Glossary 13
- Quick Start Guide 17
- 2. Connecting the Power 18
- Configuring the MNG-ETH port 19
- Contents 21
- Optimux-106 Ver. 6.1 iii 23
- Chapter 1 25
- Introduction 25
- 1.2 Physical Description 26
- 1.3 Functional Description 27
- Uplink Redundancy Option 28
- Alarms and Alarm Indications 29
- Management and Monitoring 31
- Physical Characteristics 31
- Power Requirements 31
- Plastic Enclosure 34
- Metal Enclosure 34
- Chapter 2 35
- Installation and Setup 35
- 2.2 Package Contents 36
- 2.3 Required Equipment 36
- 2.4 Mounting the Unit 37
- Connector Location 38
- Connecting to Channels 38
- Connecting to Alarm Relay 39
- Connecting to DCE 39
- 2.6 Grounding 40
- 2.7 Connecting to Power 40
- Caution 41
- Chapter 3 43
- Operation 43
- 3-1. Optimux-106 Indicators 44
- Device Information 45
- Logging In 47
- Choosing Options 48
- Navigating Tables 49
- Functional Screen Example 50
- Help Screen Example 50
- 3.5 Menu Map 51
- 3.6 Turning Off Optimux-106 52
- Chapter 4 53
- Configuration 53
- 4-2. Host IP Menu 54
- 4-2. Host Parameters 54
- Setting up the Manager List 55
- Changing a Password 56
- Listing Users 57
- 4-15. Link Menu 63
- 4-10. Uplink Parameters 63
- Configuring Local Redundancy 64
- Swapping the Software Files 65
- Viewing the Inventory 66
- Resetting Optimux-106 67
- Terminal Management Modes 67
- Chapter 5 69
- Monitoring and 69
- Diagnostics 69
- 5-2. System Status Screen 70
- 5-4. MNG-ETH Status Screen 72
- 5-5. USER-ETH Status Screen 73
- 5-6. Uplink Status Screen 74
- 5.2 Detecting Errors 75
- 5.3 Handling Alarms 75
- Displaying System Alarms 76
- Configuring Alarms 76
- List of Alarms and Events 77
- 5.4 Troubleshooting 78
- Setting Uplink Loopbacks 79
- Setting T1 Channel Loopbacks 80
- Local Optimux-106 82
- Remote Optimux-106 84
- Clearing the System Log File 85
- 5.7 Technical Support 86
- Chapter 6 87
- Software Upgrade 87
- Utilities Menu 88
- Activating the TFTP Server 89
- 6-2. TFTP Menu 90
- Telnet 91
- Using the XMODEM Protocol 92
- Using the TFTP 94
- Chapter 7 97
- Configuring a Typical 97
- Application 97
- Appendix A 99
- Pinouts 99
- A.3 Alarm Connector 100
- A.4 Control Connector 101
- Appendix B 103
- Optimux-106 MIBs 103
- B-2 Optimux-106 Ver. 6.1 104
- Customer Response Form 105
- Error Report 107
- International Headquarters 110
- North America Headquarters 110
Related products and manuals for Networking RAD Data comm Optimux-106
Networking RAD Data comm ASM-20 Specifications
(116 pages)
(116 pages)
Networking RAD Data comm T1 Specifications
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 1.155 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals