RAD Data comm Optimux-106 Specifications Page 18
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Quick Start Guide Installation and Operation Manual
2 Connecting the Power Optimux-106 Ver. 6.1
2. Connecting the Power
Before powering this unit and before connecting or disconnecting any other
cable, the protective earth terminals of this instrument must be connected to the
protective ground conductor of the mains (AC or DC) power cord. If you are using
an extension cord (power cable) make sure it is grounded as well.
Any interruption of the protective grounding conductor (inside or outside the
instrument) or disconnecting the protective earth terminal can make this unit
dangerous. Intentional interruption is prohibited.
Connecting the AC/DC Power
The Optimux-106 is supplied with a Wide Range AC/DC power supply. The
wide-range AC/DC power supply accepts current from both AC and DC sources.
From an AC source, the power supply can receive any voltage in the range of 100
VAC to 240 VAC. From a DC source, the -48 VDC power supply can receive any
voltage in the range of -40 to -72 VDC.
This unit is equipped with a standard AC-type 3-prong power input connector
located on the unit rear panel. This power input connector can be used for both
AC and DC voltage inputs. AC or DC power should be supplied to Optimux-106
through the 5-feet (1.5m) standard power cable terminated by a standard
3 prong plug.
³ To connect Optimux-106 to AC power:
1. Connect the power cable to the connector on the Optimux-106 rear panel.
2. Connect the power cable to the electricity outlet.
Connecting the DC Power
When connecting the DC power, the PWR pin must be connected to the
ungrounded line of the central battery (either − or +). The RTN pin must be
connected to the grounded line of the central battery. The GND pin must be
connected to the protected earth of the building installation.
The DC installation procedure must be performed by a qualified technician.
³ To connect Optimux-106 to -48 VDC power:
• Refer to the DC power supply connection supplement, located on the
Technical Documentation CD or at the back of the official printed version of
this manual. Also, refer to the safety instructions at the beginning of this
document.
Warning
Caution
- Optimux-106 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Glossary 13
- Quick Start Guide 17
- 2. Connecting the Power 18
- Configuring the MNG-ETH port 19
- Contents 21
- Optimux-106 Ver. 6.1 iii 23
- Chapter 1 25
- Introduction 25
- 1.2 Physical Description 26
- 1.3 Functional Description 27
- Uplink Redundancy Option 28
- Alarms and Alarm Indications 29
- Management and Monitoring 31
- Physical Characteristics 31
- Power Requirements 31
- Plastic Enclosure 34
- Metal Enclosure 34
- Chapter 2 35
- Installation and Setup 35
- 2.2 Package Contents 36
- 2.3 Required Equipment 36
- 2.4 Mounting the Unit 37
- Connector Location 38
- Connecting to Channels 38
- Connecting to Alarm Relay 39
- Connecting to DCE 39
- 2.6 Grounding 40
- 2.7 Connecting to Power 40
- Caution 41
- Chapter 3 43
- Operation 43
- 3-1. Optimux-106 Indicators 44
- Device Information 45
- Logging In 47
- Choosing Options 48
- Navigating Tables 49
- Functional Screen Example 50
- Help Screen Example 50
- 3.5 Menu Map 51
- 3.6 Turning Off Optimux-106 52
- Chapter 4 53
- Configuration 53
- 4-2. Host IP Menu 54
- 4-2. Host Parameters 54
- Setting up the Manager List 55
- Changing a Password 56
- Listing Users 57
- 4-15. Link Menu 63
- 4-10. Uplink Parameters 63
- Configuring Local Redundancy 64
- Swapping the Software Files 65
- Viewing the Inventory 66
- Resetting Optimux-106 67
- Terminal Management Modes 67
- Chapter 5 69
- Monitoring and 69
- Diagnostics 69
- 5-2. System Status Screen 70
- 5-4. MNG-ETH Status Screen 72
- 5-5. USER-ETH Status Screen 73
- 5-6. Uplink Status Screen 74
- 5.2 Detecting Errors 75
- 5.3 Handling Alarms 75
- Displaying System Alarms 76
- Configuring Alarms 76
- List of Alarms and Events 77
- 5.4 Troubleshooting 78
- Setting Uplink Loopbacks 79
- Setting T1 Channel Loopbacks 80
- Local Optimux-106 82
- Remote Optimux-106 84
- Clearing the System Log File 85
- 5.7 Technical Support 86
- Chapter 6 87
- Software Upgrade 87
- Utilities Menu 88
- Activating the TFTP Server 89
- 6-2. TFTP Menu 90
- Telnet 91
- Using the XMODEM Protocol 92
- Using the TFTP 94
- Chapter 7 97
- Configuring a Typical 97
- Application 97
- Appendix A 99
- Pinouts 99
- A.3 Alarm Connector 100
- A.4 Control Connector 101
- Appendix B 103
- Optimux-106 MIBs 103
- B-2 Optimux-106 Ver. 6.1 104
- Customer Response Form 105
- Error Report 107
- International Headquarters 110
- North America Headquarters 110
Related products and manuals for Networking RAD Data comm Optimux-106
Networking RAD Data comm ASM-20 Specifications
(116 pages)
(116 pages)
Networking RAD Data comm T1 Specifications
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 0.252 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals