RAD Data comm Optimux-106 Specifications Page 78
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 5 Monitoring and Diagnostics Installation and Operation Manual
5-10 Troubleshooting Optimux-106 Ver. 6.1
5.4 Troubleshooting
If a problem occurs, check the displayed indications and refer to
Section 3-2
and
Table 3-1
for their interpretation.
Identify the trouble symptoms and perform the actions listed under Corrective
Measures in the order given in
Table
5-10
, until the problem is corrected.
Table
5-10 Troubleshooting Chart
Trouble Symptoms Probable Cause Corrective Measures
Optimux-106 does not
respond
No power Check that both ends of the power cable are properly
connected. If the power cable is properly connected, but the
power supply still does not respond, then the power supply is
defective (see below).
If Optimux-106 is powered from a DC source, check the
polarity of the power connections.
Defective Power
Supply
Disconnect the power from both ends and replace with
another power supply.
Defective
Optimux-106
Replace the Optimux-106 unit.
PWR indicator lights in
red or yellow
Defective power
supply
Turn the respective power supply off for at least 10 minutes,
and then turn it on again.
If the PWR indicator is still red or yellow, have Optimux-106
repaired as soon as possible.
The SYNC LOSS indicator
of the Uplink lights.
External problem Activate the local loopback on Optimux-106. Check that the
SYNC LOSS and AIS indicators of the Uplink in use turn OFF.
If the indicators turn off, check the T3 interface connections,
the T3 transmission path to the remote unit, and the remote
unit.
Defective
Optimux-106
Replace the Optimux-106 unit.
Defective
Optimux-106
Activate the local loopback on Optimux-106. Check that the
SYNC LOSS and AIS indicators of the Uplink in use turn OFF. If
one of the indicators remains lit, replace Optimux-106.
None of the units
connected to a local
Optimux-106 receive the
remote equipment.
External problem Activate the local loopback on Optimux-106. Check that all
the SYNC LOSS and AIS indicators turn OFF, and that the
equipment connected to the local tributaries receives their
own transmissions. If the indicators turn OFF, the problem is
external. Troubleshoot the remote unit, and the uplink
transmission path.
Defective
Optimux-106
Replace the Optimux-106.
- Optimux-106 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Glossary 13
- Quick Start Guide 17
- 2. Connecting the Power 18
- Configuring the MNG-ETH port 19
- Contents 21
- Optimux-106 Ver. 6.1 iii 23
- Chapter 1 25
- Introduction 25
- 1.2 Physical Description 26
- 1.3 Functional Description 27
- Uplink Redundancy Option 28
- Alarms and Alarm Indications 29
- Management and Monitoring 31
- Physical Characteristics 31
- Power Requirements 31
- Plastic Enclosure 34
- Metal Enclosure 34
- Chapter 2 35
- Installation and Setup 35
- 2.2 Package Contents 36
- 2.3 Required Equipment 36
- 2.4 Mounting the Unit 37
- Connector Location 38
- Connecting to Channels 38
- Connecting to Alarm Relay 39
- Connecting to DCE 39
- 2.6 Grounding 40
- 2.7 Connecting to Power 40
- Caution 41
- Chapter 3 43
- Operation 43
- 3-1. Optimux-106 Indicators 44
- Device Information 45
- Logging In 47
- Choosing Options 48
- Navigating Tables 49
- Functional Screen Example 50
- Help Screen Example 50
- 3.5 Menu Map 51
- 3.6 Turning Off Optimux-106 52
- Chapter 4 53
- Configuration 53
- 4-2. Host IP Menu 54
- 4-2. Host Parameters 54
- Setting up the Manager List 55
- Changing a Password 56
- Listing Users 57
- 4-15. Link Menu 63
- 4-10. Uplink Parameters 63
- Configuring Local Redundancy 64
- Swapping the Software Files 65
- Viewing the Inventory 66
- Resetting Optimux-106 67
- Terminal Management Modes 67
- Chapter 5 69
- Monitoring and 69
- Diagnostics 69
- 5-2. System Status Screen 70
- 5-4. MNG-ETH Status Screen 72
- 5-5. USER-ETH Status Screen 73
- 5-6. Uplink Status Screen 74
- 5.2 Detecting Errors 75
- 5.3 Handling Alarms 75
- Displaying System Alarms 76
- Configuring Alarms 76
- List of Alarms and Events 77
- 5.4 Troubleshooting 78
- Setting Uplink Loopbacks 79
- Setting T1 Channel Loopbacks 80
- Local Optimux-106 82
- Remote Optimux-106 84
- Clearing the System Log File 85
- 5.7 Technical Support 86
- Chapter 6 87
- Software Upgrade 87
- Utilities Menu 88
- Activating the TFTP Server 89
- 6-2. TFTP Menu 90
- Telnet 91
- Using the XMODEM Protocol 92
- Using the TFTP 94
- Chapter 7 97
- Configuring a Typical 97
- Application 97
- Appendix A 99
- Pinouts 99
- A.3 Alarm Connector 100
- A.4 Control Connector 101
- Appendix B 103
- Optimux-106 MIBs 103
- B-2 Optimux-106 Ver. 6.1 104
- Customer Response Form 105
- Error Report 107
- International Headquarters 110
- North America Headquarters 110
Related products and manuals for Networking RAD Data comm Optimux-106
Networking RAD Data comm ASM-20 Specifications
(116 pages)
(116 pages)
Networking RAD Data comm T1 Specifications
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 3.413 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals