RAD Data comm Optimux-106 Specifications Page 91
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Operation Manual Chapter 6 Software Upgrade
Optimux-106 Ver. 6.1 Upgrading Optimux-106 Software via the File Utilities Menu 6-5
Transfer Status Current status of the TFTP download.
No operation No TFTP transfer is in process
Connecting Initiating a TFTP connection.
Transferring data TFTP data transfer is in process.
Ended Time out The transfer terminated because the Retry Timeout or
Total Timeout was exceeded.
Ended OK The file was successfully transferred.
Error The transfer terminated because an error occurred. Check
the Transfer Error parameter for details about the error.
Transfer Error No error
Error resources
Error timout
Error use msg
Error nofile
Error acceess
Error disk full
Error illegal op
Error bad tid
Error exists
Error no user
Error code when Transfer Status is Error. This parameter
provides specific details of the error that occurred while
attempting to download the file.
This parameter is set to No error unless an error is
detected.
2. From the TFTP menu, perform the following steps:
1. Choose Server IP and enter the IP address of the server from which you
want to download the new software file.
2. Choose Remote File Name and enter the name of the file you want to
download.
3. Choose Command and then choose Software download.
The download process begins. The Transfer Status field indicates the
current status of the download.
Downloading a New Software Release via XMODEM
•
•
Installation of the new software releases via XMODEM is not possible over
Telnet.
•
To minimize the software downloading time, it is recommended to configure
the CONTROL port to the highest available data rate.
³ To download a new software release via XMODEM:
1. From the SW & File Transfer menu, select XMODEM (Utilities > File Utilities >
SW & File Transfer > XMODEM).
Optimux-106 responds with the following string:
Notes
- Optimux-106 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Glossary 13
- Quick Start Guide 17
- 2. Connecting the Power 18
- Configuring the MNG-ETH port 19
- Contents 21
- Optimux-106 Ver. 6.1 iii 23
- Chapter 1 25
- Introduction 25
- 1.2 Physical Description 26
- 1.3 Functional Description 27
- Uplink Redundancy Option 28
- Alarms and Alarm Indications 29
- Management and Monitoring 31
- Physical Characteristics 31
- Power Requirements 31
- Plastic Enclosure 34
- Metal Enclosure 34
- Chapter 2 35
- Installation and Setup 35
- 2.2 Package Contents 36
- 2.3 Required Equipment 36
- 2.4 Mounting the Unit 37
- Connector Location 38
- Connecting to Channels 38
- Connecting to Alarm Relay 39
- Connecting to DCE 39
- 2.6 Grounding 40
- 2.7 Connecting to Power 40
- Caution 41
- Chapter 3 43
- Operation 43
- 3-1. Optimux-106 Indicators 44
- Device Information 45
- Logging In 47
- Choosing Options 48
- Navigating Tables 49
- Functional Screen Example 50
- Help Screen Example 50
- 3.5 Menu Map 51
- 3.6 Turning Off Optimux-106 52
- Chapter 4 53
- Configuration 53
- 4-2. Host IP Menu 54
- 4-2. Host Parameters 54
- Setting up the Manager List 55
- Changing a Password 56
- Listing Users 57
- 4-15. Link Menu 63
- 4-10. Uplink Parameters 63
- Configuring Local Redundancy 64
- Swapping the Software Files 65
- Viewing the Inventory 66
- Resetting Optimux-106 67
- Terminal Management Modes 67
- Chapter 5 69
- Monitoring and 69
- Diagnostics 69
- 5-2. System Status Screen 70
- 5-4. MNG-ETH Status Screen 72
- 5-5. USER-ETH Status Screen 73
- 5-6. Uplink Status Screen 74
- 5.2 Detecting Errors 75
- 5.3 Handling Alarms 75
- Displaying System Alarms 76
- Configuring Alarms 76
- List of Alarms and Events 77
- 5.4 Troubleshooting 78
- Setting Uplink Loopbacks 79
- Setting T1 Channel Loopbacks 80
- Local Optimux-106 82
- Remote Optimux-106 84
- Clearing the System Log File 85
- 5.7 Technical Support 86
- Chapter 6 87
- Software Upgrade 87
- Utilities Menu 88
- Activating the TFTP Server 89
- 6-2. TFTP Menu 90
- Telnet 91
- Using the XMODEM Protocol 92
- Using the TFTP 94
- Chapter 7 97
- Configuring a Typical 97
- Application 97
- Appendix A 99
- Pinouts 99
- A.3 Alarm Connector 100
- A.4 Control Connector 101
- Appendix B 103
- Optimux-106 MIBs 103
- B-2 Optimux-106 Ver. 6.1 104
- Customer Response Form 105
- Error Report 107
- International Headquarters 110
- North America Headquarters 110
Related products and manuals for Networking RAD Data comm Optimux-106
Networking RAD Data comm ASM-20 Specifications
(116 pages)
(116 pages)
Networking RAD Data comm T1 Specifications
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 0.206 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals