RAD Data comm Optimux-106 Specifications Page 89
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Operation Manual Chapter 6 Software Upgrade
Optimux-106 Ver. 6.1 Upgrading Optimux-106 Software via the File Utilities Menu 6-3
Verifying the Optimux-106 Host Parameters
The Optimux-106 host must have host IP parameters configured according to
your network requirements. Otherwise you will not be able to establish a proper
communication session with the TFTP server. Refer to the following manual
section for additional information:
•
Connecting to the ASCII Terminal
in
Chapter 2
•
Working with Terminal
in
Chapter 3
•
Configuring IP Host Parameters
and
Configuring the Host Encapsulation
in
Chapter 4
.
³ To verify the Optimux-106 host parameters:
• Display the Host IP menu (Configuration > System Configuration >
Management > Host IP), and verify that the host IP address, IP mask and
default gateway are configured according to your network requirements.
Optimux-106
Host IP
Host IP address (172.17.161.73)
Host IP mask (255.255.255.0)
Host default gateway (172.17.161.1)
Read community (public)
Write community (public)
Trap community (public)
>
ESC-prev. menu; !-main menu; &-exit; @-scroll
Figure
6-1. Configuring the Host
Activating the TFTP Server
Once the TFTP server is activated on the PC, it waits for any TFTP file transfer
request originating from the product, and carries out the received request
automatically.
Transferring Software and Configuration Files
section in
Chapter 4
explains how to prepare your PC for the TFTP file transfer.
³ To run the TFTP server:
• Activate a TFTP server application, such as 3Cdaemon (available from
www.3com.com) or PumpKIN (available from http://kin.klever.net/pumpkin/).
Downloading the New Software Release File to Optimux-106
Optimux-106 stores two software versions, each of them in one of the two
partitions of its flash memory, which also contains a boot program. The software is
stored in compressed format. The active version is decompressed and loaded into
the Optimux-106 RAM upon power-up. The passive software is kept for backup
purposes. By default, Optimux-106 is delivered with the active software only.
- Optimux-106 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Glossary 13
- Quick Start Guide 17
- 2. Connecting the Power 18
- Configuring the MNG-ETH port 19
- Contents 21
- Optimux-106 Ver. 6.1 iii 23
- Chapter 1 25
- Introduction 25
- 1.2 Physical Description 26
- 1.3 Functional Description 27
- Uplink Redundancy Option 28
- Alarms and Alarm Indications 29
- Management and Monitoring 31
- Physical Characteristics 31
- Power Requirements 31
- Plastic Enclosure 34
- Metal Enclosure 34
- Chapter 2 35
- Installation and Setup 35
- 2.2 Package Contents 36
- 2.3 Required Equipment 36
- 2.4 Mounting the Unit 37
- Connector Location 38
- Connecting to Channels 38
- Connecting to Alarm Relay 39
- Connecting to DCE 39
- 2.6 Grounding 40
- 2.7 Connecting to Power 40
- Caution 41
- Chapter 3 43
- Operation 43
- 3-1. Optimux-106 Indicators 44
- Device Information 45
- Logging In 47
- Choosing Options 48
- Navigating Tables 49
- Functional Screen Example 50
- Help Screen Example 50
- 3.5 Menu Map 51
- 3.6 Turning Off Optimux-106 52
- Chapter 4 53
- Configuration 53
- 4-2. Host IP Menu 54
- 4-2. Host Parameters 54
- Setting up the Manager List 55
- Changing a Password 56
- Listing Users 57
- 4-15. Link Menu 63
- 4-10. Uplink Parameters 63
- Configuring Local Redundancy 64
- Swapping the Software Files 65
- Viewing the Inventory 66
- Resetting Optimux-106 67
- Terminal Management Modes 67
- Chapter 5 69
- Monitoring and 69
- Diagnostics 69
- 5-2. System Status Screen 70
- 5-4. MNG-ETH Status Screen 72
- 5-5. USER-ETH Status Screen 73
- 5-6. Uplink Status Screen 74
- 5.2 Detecting Errors 75
- 5.3 Handling Alarms 75
- Displaying System Alarms 76
- Configuring Alarms 76
- List of Alarms and Events 77
- 5.4 Troubleshooting 78
- Setting Uplink Loopbacks 79
- Setting T1 Channel Loopbacks 80
- Local Optimux-106 82
- Remote Optimux-106 84
- Clearing the System Log File 85
- 5.7 Technical Support 86
- Chapter 6 87
- Software Upgrade 87
- Utilities Menu 88
- Activating the TFTP Server 89
- 6-2. TFTP Menu 90
- Telnet 91
- Using the XMODEM Protocol 92
- Using the TFTP 94
- Chapter 7 97
- Configuring a Typical 97
- Application 97
- Appendix A 99
- Pinouts 99
- A.3 Alarm Connector 100
- A.4 Control Connector 101
- Appendix B 103
- Optimux-106 MIBs 103
- B-2 Optimux-106 Ver. 6.1 104
- Customer Response Form 105
- Error Report 107
- International Headquarters 110
- North America Headquarters 110
Related products and manuals for Networking RAD Data comm Optimux-106
Networking RAD Data comm ASM-20 Specifications
(116 pages)
(116 pages)
Networking RAD Data comm T1 Specifications
(34 pages)
(34 pages)
© 2020, manymanuals.com. All rights reserved. | 1.843 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals